Shark Rotator Powered Lift-Away Troubleshooting - iFixit
WEBFollow the instructions to restart the motor protective thermostat. Turn off and unplug the vacuum. Remove and empty the dust cup and clean both filters. Inspect for obstructions in the hose, accessories and/or inlet openings. Allow the vacuum to cool for at least 45 minutes. Plug in the vacuum and resume.
Shark Navigator Lift-Away Deluxe NV360 Power Button …
WEBStep 17. Locate the protrusion on the metal connector of the red wire. Push down on the protrusion with the metal spudger while pushing the connector on the red wire away from the power button with your fingers. Pull and wiggle the wire away by its connector with your fingers until it is completely detached from the connector on the power button.
Shark Rotator Powered Lift-Away Speed Roller Brush Replacement
WEBThe roller brush can have debris that will cause the vacuum to not work properly. It is important that you always clean your roller brush after every use, so that your Shark Rotator Powered Lift Away Speed Vacuum can perform at it's best. This guide will show you how to change your roller brush if it becomes damaged or is broken.
Shark Navigator Lift-Away Pro Troubleshooting - iFixit
WEBUnplug the vacuum. Check for a clogged hose or filter; unclog the hose and replace the filter. Wait 45 minutes for the vacuum to cool; then plug in the vacuum. Turn the power switch to the “I-On” position to start the vacuum. If the vacuum still does not start, contact Customer Service at 1-800-798-7398.
Shark Rotator Powered Lift-Away Speed Troubleshooting
WEBClutch the “Lift-Away” handle, and remove the vacuum for the floor stand. Flip the Remove the hose clip, and pull the handle away from the wand. Look down the wand for anything blocking the air flow. To remove the hose, press the grey release tab where the hose meets the dust collector. Pull the hose off.
Shark Rotator Powered Lift-Away Roller Brush Replacement
WEBRemove the 13 screws (circled in yellow) using a phillips screwdriver. Be sure to keep track of which screws go into which hole. Remove the one screw (circled in red) that has a Torx head (might be Phillips head on some models). The Torx screw is hidden under a rubber gasket. Carefully, lift up the gasket without damaging it to access this screw.
Shark Rotator Powered Lift-Away Speed Belt Replacement
WEBIntroduction. Go to step 1. The Shark Rotator Powered Lift-Away has one rotatory belt. The belt is responsible for the mechanical rotations of the brushroll. Without it, the vacuum will not function. The vacuum's belt is designed to last approximately 7 years. Replacement of the belt is needed to keep the vacuum at optimal working condition.
Shark Rotator Lift-Away Speed Belt Replacement - iFixit
WEBStep 1 Brushroll. Make sure the vacuum is turned off and unplugged before proceeding. Locate the release button at the top of the vacuum pod next to the handle. Use the handle to lift the pod up off of the vacuum nozzle while pressing the release button. Removing the pod is optional, but it may be easier to locate blockages or access the motor ...
SOLVED: Why won’t my vacuum turn on? - Shark Rotator NV502
WEBOct 20, 2016 — All Time: 232,688. First, make sure the vacuum is plugged in. If the vacuum is plugged in and the switch is pushed on, but it's not turning on then try to reset your circuit breaker or reset the motor thermostat. The steps to reset the motor thermostat can be found in the troubleshooting guide. - Shark Rotator NV502.
Shark DuoClean Powered Lift-Away Speed Drive Belt Replacement
WEBStep 5. Use the T20 screwdriver to remove the six 19 mm screws by turning counterclockwise. Use the T20 screwdriver to remove the one 12 mm screw by turning counterclockwise. Use the T10 screwdriver to remove the four 14 mm screws by turning counterclockwise.